Search results

When configuring a new VLAN on Cisco IOS switches, which configuration parameter is required? A. VLAN ID B. VLAN MTU C. native VLAN ID D. VLAN map E. VLAN name

Refer to the show command exhibit. Which statement is true? A. It shows the contents of the failed configuration. B. It shows the result of the target configuration merged with the running configuration. C. It shows the contents of the uncommitted configuration. D. It shows the contents of...

On Cisco IOS XR software, what is the default commit option? A. best-effort B. force C. psuedo-atomic D. replace

Within an MPLS domain, which table is used by the label switch routers to make forwarding decision when a labeled packet is received? A. FIB B. LIB C. CEF D. LFIB E. RIB

Your switch network has been configured to support multiple VLANs. In order for the users on one VLAN to communicate with users on another VLAN, which additional configuration is required? A. Enable a routing protocol like EIGRP on a router or on a Layer 3 capable switch B. Enable a switch...

On Cisco routers, the address-family configuration command in BGP configuration mode is used to enable which BGP feature? A. multiprotocol BGP B. BGP policy accounting C. BGP communities D. BGP route policy

ควรฟังก่อนตาย คู่มือมนุษย์(บทนำ) 1/34

On Cisco IOS XR software, which two of the address-family command options in IS-IS configuration mode are valid? (Choose two) A. address-family clns B. address-family ipv4 unicast C. address-family vpnv6 D. address-family ipv6 unicast E. address-family vpnv4

Code: http://www.mywindowsthai.com/virusshortcut.html

You want to configure HSRP between a Cisco IOS and a Cisco IOS XR router for the 192.0.2.0/24 subnet. Half of the PCs on the 192.0.2.0/24 subnet are configured to use 192.0.2.1 as the default gateway, and the other half of the PCs are configured to use 192.0.2.254 as the default gateway. The...

Which Cisco router platform supports running either the Cisco IOS or IOS XR operating system? A. Cisco CRS B. Cisco ASR1k C. Cisco ASR9k D. Cisco ISR-G2 E. Cisco 12000 GSR

When upgrading a Cisco ASR 1001 Router, when is the request platform software package expand file bootflash:image-name command required? A. to perform Cisco IOS ISSU on the standby route processor B. to run the router using individual subpackages C. to copy the consolidated Cisco IOS XE image...

Which IPv6 address block is reserved for 6to4 tunneling? A. 2000::/16 B. 2001::/16 C. 2002::/16 D. 3ffe::/16 E. fe80::/16

Refer to the topology diagram in the exhibit. Which two interface configuration commands on the Cisco ME 3400-1 switch Fa 0/1 interface are required to support the VLANs for Customer A to be trunked across the service provider network? (Choose two.) A. switchport mode trunk B. switchport...

Refer to the partial configurations: Quote: !ME3400 ! ip routing ! vlan 10 vlan 20 interface Fa0/1 switchport access vlan 10 interface Fa0/2 switchport access vlan 20 ! What additional configurations are required to enable inter-VLAN routing for VLANs 10 and 20 on the Cisco ME 3400 switch...

Refer to the configuration: Quote: SwitchX#configure terminal SwitchX(config)#interface fa0/11 SwitchX(config-if)#switchport mode trunk SwitchX(config-if)#end Which statement is true? A. VLAN 1 traffic is sent untagged on the fa0/11 trunk port. B. All VLANs traffic, including the native...

A VLAN is a logical grouping of switch ports that belong to which two of these? (Choose two.) A. the same IP subnet B. the same broadcast domain C. the same collision domain D. the same virtual routing and forwarding instance E. the same virtual switch cluster

Which four statements about REP configurations on a Cisco ME 3400 switch port are true? (Choose four.) A. If a failure occurs within the segment, the blocked port goes to the forwarding state after it goes through the listening state and the learning state. B. A REP segment cannot be wrapped...

On Cisco IOS XR software, how is LDP enabled on an interface? A. LDP is enabled globally on all interfaces, using the mpls ldp global configuration command. B. LDP is enabled on each interface, using the mpls ip interface configuration command. C. LDP is enabled on each interface, using the...

Refer to the exhibit. Which three statements about MPLS LDP operations are true? A. The 16003 and 16010 labels are learned from the 192.168.112.40 LDP neighbor. B. The Unlabeled outgoing label for 10.10.10.100/32 indicates that a label pop is required when sending packets to the 10.10.10.1...