THAI CPE

NE Router(NE20/40/40E/80E/5000E),ME60,CX600,Ethernet LAN switch(S9300/S5300/S3300/S2300),.:
support.huawei.com/support

VPLS:

Cisco > Huawei command:

eNSP (Huawei Network Simulator):
support.huawei.com/enterprise/productNewOffering?idAbsPath=7919710|21782036|21782103|21782135|9017384&pid=9017384&from=soft&productname=eNSP

Configuring a Martini VLL (xconnect) to Access an L3VPN:

blog.network-solution.net/configuring-a-martini-vll-to-access-an-l3vpn

Configuring a VSI (VPLS) to Access an L3VPN:

1. Configure an IP address for physical interfaces and loopback interfaces.
   
   
2. Create VE2/0/2 to terminate the MPLS L2VPN: 2/0 means use throughput of slot 2
   
   system-view
   sysname NPE
   interface virtual-ethernet2/0/2
     ve-group 1 l2-terminate
     quit
   
   Create VE2/0/3 to access the MPLS L3VPN.
   
   interface virtual-ethernet2/0/3
     ve-group 1 l3-access
     quit
   
   After the configuration is complete, run display virtual-ethernet ve-group command. To view the binding relationship between VE interfaces and a VE-group.
   
   
3. Run an IGP on the VSI access network. ISIS is used in the example.

gns3vault.com/labs/bgp

• BGP Basic:
  interface Ethernet0/0/0
    ip address 192.168.12.1 255.255.255.0
  #
  bgp 100
    peer 192.168.12.2 as-number 200
    network 2.2.2.0 24
  #
  >display bgp peer
  >display bgp routing-table
  >display ip routing-table
  
  
• BGP IBGP/EBGP Local Preference MED:
  ospf
    area 0
      network 192.168.12.0 0.0.0.255
  #
  bgp 100
    peer 2.2.2.2 connect-interface LoopBack0 : update-source
    peer 1.1.1.1 next-hop-local : next-hop-self
  
  
• Static Route with track NQA (NQA: Cisco IP SLA):
  
  nqa test-instance <NQA test administrator name> <NQA test test name>
   test-type icmp
   destination-address ipv4 <x.x.x.x>
   frequency <Seconds>
   start now
  #
  ip route-static <Destination IP> <Length IP address mask> <Gateway address> track nqa <NQA test administrator name> <NQA test test name>
  
  nqa test-instance x 1
   test-type icmp
   destination-address ipv4 1.1.1.1
   frequency 10
   start now
  #
  ip route-static 2.2.2.0 255.255.255.0 3.3.3.3 track nqa x 1
  
  display nqa results
  
  If nqa destination-address is unreachable, it won't appear in the routing-table

A Packet's Adventures on Huawei Routers:

1. Introduction:
   forum.huawei.com/enterprise/forum.php?mod=viewthread&tid=200095
   
   
2. Switching, Address:
   forum.huawei.com/enterprise/forum.php?mod=viewthread&tid=215113
   
   
3. Packet Receiving:
   forum.huawei.com/enterprise/forum.php?mod=viewthread&tid=218321
   
   
4. Traffic Control:
   forum.huawei.com/enterprise/forum.php?mod=viewthread&tid=218431
   
   
5. QoS Basics(1):
   forum.huawei.com/enterprise/forum.php?mod=viewthread&tid=219729
   
   
6. QoS Basics(2):
   forum.huawei.com/enterprise/forum.php?mod=viewthread&tid=219777
   
   
7. QoS Processing:
   forum.huawei.com/enterprise/forum.php?mod=viewthread&tid=220011
   
   
8. Fragmentation & Reassembly, Multicast & Broadcast Replication, NAT, Packet Filtering / ACL, Policy-based Routing (PBR):
   forum.huawei.com/enterprise/forum.php?mod=viewthread&tid=220197
   
   
9. A journey of Protocol Packets:
   forum.huawei.com/enterprise/thread-221889.html